To properly measure your counter space, you’ll need to create a basic sketch drawing of its dimensions. For this, you’ll need the following tools:
Pen/pencil and paper
Measuring tape
Calculator
Although it’s not necessary in receiving a quote, your sketch is a vital step in measuring for new countertops. It provides you with a basic blueprint that you can add details to as you move forward with your renovation project. It also allows us to give you the most accurate estimate from the start!
Just keep in mind that this is only a rough sketch and does not necessarily need to be up to scale.
While none of the measurements in your sketch need to be exact, it’s important to mark out the following key locations:
Sinks, be it a drop-in, under-mount, or farm sink.
Cooktop or stove (for stoves, you’ll need to create a break in your sketch where there will not be any countertop)
Any exposed edges that will need to be polished (Which will factor into the overall price of your new countertop)
Any appliances that will be next to the counter.
Once you’ve made a basic sketch drawing of your counter space, it’s time to start filling it in with measurements.
For this, you’ll need to measure the length (L) and width (W) of each section of counter space in your room. (The standard width for base cabinets is roughly 24”).
Next, take these measurements and mark them on your sketch. Keep in mind that it’s usually a good idea to add about an inch and a half (1.5”) to each width to accommodate for the countertop’s overhang.
And always round up to the nearest inch. Not only does this make calculations easier, but it also helps you avoid under-ordering the amount of material that you’ll need for the job.
Lastly, it’s best to always measure in inches first, then if you need to, you can easily convert this into feet. And using whole numbers makes estimating your counter space much easier.
In addition to mapping out the dimensions of your countertop, you’ll also want to include locations for your sink, stovetop, and any edges that are up against appliances or need to be polished.
Take measurements for these, as well, and make sure to add them to your sketch.
Any areas that are occupied by these items will need to be subtracted from your overall countertop measurements, which is important if you’re trying to estimate the cost of a new installation.
Again, these measurements do not need to be precise since your installation company will take more accurate measurements before cutting your new granite or quartz countertops to shape.
Although not every countertop will be a simple rectangular shape, the basic idea behind taking your measurements will remain more or less the same.
For example, let’s just say that you wanted to have a curved, or wavy edge on your countertop.
The fabricator will do their best to cut this as one single, solid piece. Therefore, you’d want to measure the curve at its widest point and multiply this by its total length.
This will give you the total size of the slab required for your counter, and the fabricator would then take additional measurements to accommodate the irregular shape.
One of the most important things to remember when taking measurements is to always measure twice, just to be sure your drawing is accurate.
Also, keep the following tips in mind when estimating the size and cost of your renovation project.
It’s important to understand most stone countertop materials are sold by the slab, which is on average 41 square feet.
So you’ll need to budget accordingly. Even if you have a smaller kitchen and only require 1.5 slabs, you’ll still need to purchase two slabs to complete your project.
If you decide you want to add a backsplash using the same material as your countertop, don’t forget to include it on your sketch.
For this, add an extra 4 inches or so to the total length of your countertops. Just remember that if you want a higher backsplash, this will obviously affect the amount of material needed, as well as the overall cost of your estimate.
But in the event that you needed to order more material than you need for your counters (for example, needing to buy 2 full slabs when you’ll only need 1.5), you can use this surplus for your backsplash.
At the same time, don’t forget to include any extra overhangs that you may want in certain areas. Many homeowners choose to have a wider overhang on kitchen islands or peninsulas where people might sit or use as a preparation area.
We recommend no more than an 8” to 12” overhang. Anything more than 12” will require additional support.
After creating your sketch and taking measurements, contact us for a consultation on your kitchen or bathroom renovation project.
Once we’ve finalized your estimate and have taken your order, we’ll visit your home and take precise measurements of your countertops before we begin cutting your slabs down to size.
In the end, you’ll be amazed at how amazing your new kitchen or bathroom countertops look!
Measuring your countertop for countertops can seem like an intimidating task. But with the right tools and a step-by-step guide, it can be a straightforward process. Here’s what you’ll need:
Pen/pencil and paper
Measuring tape
Calculator
Creating a basic sketch drawing of your counter space is a vital step in measuring for new countertops. It provides you with a basic blueprint that you can add details to as you move forward with your renovation project.
Just keep in mind that this is only a rough sketch and does not necessarily need to be up to scale.
NOTE: If you’re having a hard time measuring, don’t worry! Our team of experts is here to help. During the template stage we visit your home and take precise measurements before we start cutting your countertops down to size. We use client-provided sketches to provide you with accurate estimates from the beginning.
Once you’ve made a basic sketch drawing of your counter space, it’s time to start filling it in with measurements. In addition to mapping out the dimensions of your countertop, you’ll also want to include locations for your sink, stovetop, and any edges that are up against appliances or need to be polished.
Take measurements for these, as well, and make sure to add them to your sketch. Any areas that are occupied by these items will need to be subtracted from your overall countertop measurements, which is important if you’re trying to estimate the cost of a new installation.
Although not every countertop will be a simple rectangular shape, the basic idea behind taking your measurements will remain more or less the same. For example, if you wanted to have a curved, or wavy edge on your countertop, you’d want to measure the curve at its widest point and multiply this by its total length.
This will give you the total size of the slab required for your counter, and our team would then take additional measurements to accommodate the irregular shape.
After creating your sketch and taking measurements, schedule a consultation on our site. Once we’ve finalized your estimate and have taken your order, we’ll visit your home and take precise measurements and templates for your countertops before they begin cutting your slabs down to size.